Westinghouse 7222900 Instalační příručka stáhnout pdf

ETL-ES-Origami-WH10

Unpack and inspect fan carefully to be certain all contents are included.

Turn off power at fuse box to avoid possible electrical shock.

Use metal outlet box suitable for fan support (must support 35 lbs).

Before attaching fan to outlet box, ensure the outlet box is securely

fastened by at least two points to a structural ceiling member (a loose

box will cause the fan to wobble).

PREPARING FOR INSTALLATION

ANTES DE LA INSTALACIÓN

Quite el envoltorio e inspeccione detenidamente el ventilador para verificar

que todas las piezas estén incluidas. Apague la alimentación en la caja de

fusibles para evitar la posibilidad de descarga eléctrica.

Use una caja de embutir de metal adecuada para soportar un ventilador

(debe soportar 35 libras). Antes de fijar el ventilador a la caja de embutir

asegúrese de que la misma esté fijada de manera segura en por lo menos

dos puntos a un miembro estructural del cielo raso (una caja suelta haría

que el ventilador oscile).

1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1 - ANTES DE LA INSTALACIÓN

6ETL-ES-Origami-WH10Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical

Strany 2 - MOUNTING BRACKET INSTALLATION

15ETL-ES-Origami-WH10SECURE TO CEILINGASEGURE EL VENTILADOR AL CIELORRASO17The canopy has two mating slots (1) and two mating holes (2). Position both

Strany 3 - Elija una OPCIÓN DE MONTAJE

16ETL-ES-Origami-WH10LIGHT FIXTURE INSTALLATIONINSTALACIÓN DEL ARTEFACTO LUMINOSO18Install light bulbs.Instale las bombillas de luz.19 Attach glass to

Strany 4 - NORMAL DOWNROD OPTION

17ETL-ES-Origami-WH1020 Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain couplin

Strany 5 - EXTENDED DOWNROD OPTION

7ETL-ES-Origami-WH10Remove the screws from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the ca

Strany 6

8ETL-ES-Origami-WH10MOUNTING BRACKET INSTALLATIONINSTALACIÓN CON SOPORTE DE MONTAJEInstall mounting bracket to outlet box in ceiling using the screws

Strany 7

9ETL-ES-Origami-WH10213NORMAL DOWNROD OPTIONOPCIÓN CON VARILLA VERTICAL PARA CIELORRASO NORMAL1234Place downrod assembly (1) into canopy (2) and coupl

Strany 8 - MOUNTING

10ETL-ES-Origami-WH108Loosen downrod ball (1) from downrod (2) by removing set screw (3).Afloje la esfera de la varilla vertical (1) de la varilla ver

Strany 9 - OPCIÓN DE CABLEADO

11ETL-ES-Origami-WH10EXTENDED DOWNROD OPTIONOPCIÓN CON VARILLA VERTICAL MÁS LARGA10Re-install pin into extended downrod, and slide downrod ball up to

Strany 10 - SECURE TO CEILING

12ETL-ES-Origami-WH10Attach blade assembly to motor using the noise-dampening motor gaskets and motor screws provided. Tighten screws securely.Fije el

Strany 11 - LIGHT FIXTURE INSTALLATION

13ETL-ES-Origami-WH10MOUNTINGMONTAJE14With bracket holding fan assembly, make electrical connections using the following step for wiring instructions.

Strany 12 - ETL-ES-Origami-WH10

14ETL-ES-Origami-WH10WIRING OPTIONSOPCIÓN DE CABLEADO16Follow diagram above to make wiring connections for wall control operation.15Follow diagram abo